304 North Cardinal St.
Dorchester Center, MA 02124
304 North Cardinal St.
Dorchester Center, MA 02124
I built a large wood table using the black metal bases from the ones we already had!
Remember years ago when I was looking for a large, affordable coffee table? I wanted something around four by four feet for our family room — the space is big and the tiny table we had there was getting swallowed up.
It worked perfectly! We got the size we wanted for only around $200 — WAY less than anything I found online.
Each table had a faux wood top that was surrounded with trim:
This post may contain affiliate links for your convenience.
I may earn a small commission when you make a purchase through links.
I’d been thinking recently about changing this up a bit and making a new tabletop…something in one solid piece that would look a little more custom.
We didn’t mind the two tables, but I knew it would be easier to have everything on an even surface. The faux wood has seen a little bit of wear over the years as well.
And I could just see the big wood top in my mind and knew it would look GREAT in our family room.
So I finally got to it last week. I took the two tops off the existing table legs (you know I kept those for a future project!) and got to work on the new top.
I determined the size I needed for the new wood table first. I made sure to measure the width of the metal bases together, not the tops that was already on the tables, because I wanted my new tabletop to be flush with the metal frames.
My plan was to add some wood trim around the edges for a traditional look. The size of your top is totally up to you — have it extent out a big from the metal to make an even bigger coffee table!
My final size was 44×44 inches, so I had a big 4×8 sheet of birch plywood cut down at the hardware store. Most large stores will cut wood down for you — it is such a great service that I have relied on numerous times over the years!
There’s usually a “good” side of the wood (most often the side that doesn’t have a sticker). It’s normally pretty apparent from the look of the wood too.
If you’re new to DIY or staining, I suggest trying out your process on the “wrong” side or a scrap piece first. This will help to perfect the process and you’ll be able to see what your stain will look like on the wood.
I laid my 44″ square down in our garage and did a light sanding of the edges and top first. Nothing crazy…you just want to knock down any texture or splintering.
If you are staining, this step is by far the most important. Using a preconditioner on your wood before staining will make the whole process go SO much easier!:
It goes on clear and is super easy to apply — literally just slap it on. 🙂
The conditioner penetrates the wood so that the stain will go on evenly.
When you apply stain without conditioner, you need to work pretty quickly to ensure that there are no ‘stop and start’ spots. This will give you a good idea of what I’m talking about:
If I had applied the stain like that without the conditioner, the heavier overlapped parts would show on the final project.
You can stain a piece just fine without the conditioner (I did for years before I discovered it!)…but you do have to work quicker and be sure to keep things smooth and even as you apply.
See how the uneven appearance disappears when I wiped the excess stain away?:
The conditioner only adds a few minutes to the project and you can stain almost immediately.
Make sure to let the stain dry well before adding a protective coat. I like a semi-gloss polyurethane:
This was actually my second coat. At first I thought I had grabbed my wipe on poly that you can apply by hand with a clean rag. Turns out it was a traditional version that needs to be brushed on.
I quickly realized my mistake because it was not going on well at all. But I had to let it dry and then sand down the messy parts before I added a final coat of brush on polyurethane.
I’ve done staining and DIY projects for years and still mess up plenty! 😁
After the poly was dry, I brought the tabletop into the family room and laid it face down on the floor. I placed the original table frames on the back and made sure they were as even as possible before attaching them:
Always predrill your screw holes to ensure there is no splitting in the wood. I like to mark where to stop with painter’s tape so I don’t drill all the way through the wood:
Also, make sure to use screws that are shallow enough that they won’t penetrate the finished side of the tabletop! (The screws that came with the original tops were too long, so I used some out of my stash).
After all the screws were in, I flipped it over and was already SO thrilled with how it looked!:
You can sand or paint that edging to match the rest of the wood.
I prefer a traditional detail, so I cut down 1x2s to wrap the edges of the wood top:
I used a little bit of wood glue and nailed them in as well. Take care as you attach so that your nails don’t come through the top or bottom of your table!
Don’t use excessively long nails and be sure to hold the nailer straight and level as you go.
These 1x2s have a very sharp corner, so I like to soften them up a bit. If you haven’t stained yet, you can use a sander to knock down the corners a bit, but I prefer to just take something round like a screwdriver and pull it along the edges:
It works as a router and knocks down that hard corner with ease. (At least on softer woods like birch and pine.)
By the way, my 1x2s for the frame around the tabletop were pine, the top was birch. I gave the pine two coats of stain (one coat on the birch table) and they matched up really well.
I did take a sander to where the mitered cuts met up at the corners. Just a light sanding is all they needed to cut down that sharp edge.
Make sure to reapply the stain conditioner before you touch up your stain on any sanded parts! If you don’t you’ll have a slightly uneven stain application.
Not the end of the world if you forget. I’ve done that plenty and I like to say that it adds to the character. 😉
Here’s my dirty little secret — I rarely fill my nail holes. I’ve tried a bunch of stainable fillers and they just don’t take stain how I’d like. If you have one you like please let me know!:
I find the nail holes are not that noticeable in the end…with a filler they are more pronounced.
After all the touch ups were done and dry, I applied a coat of poly to the 1x2s around the edges as well. Let it all dry fully before putting any items on the wood:
Other than my little mess up with the first polyurethane coat, this was a really quick and easy project!
We LOVE it! I know it’s a great project when the family comments on much they love something!:
The wood adds so much warmth to our family room. I just LOVE that lovely Provincial stain.
The two tables together were great, this just makes more of a statement. Our great room is pretty spacious and can take large furniture:
I hesitated for months on this project because the price of wood has gone up so much. The 4×8 sheet of plywood was $80…I think that’s double what I used to pay!
But I came in under $100 for all the materials and I have some leftover for future projects. It was totally worth it in the end! I feel like it upped the cozy factor in here big time:
Now we have a much bigger surface for games, food…whatever. I’m so glad I finally tackled this quick project:
Stain: Provincial by Minwax
Wood tabletop: 3/4 inch birch plywood
Wood edging: 1×2 select pine
Protective coat: semi-gloss polyurethane